SEKURE DGP2-648 Manuel d'installation télécharger pdf (Page 43)

DIGIPLEXNE CONTROL PANEL 41

14 WINLOAD SOFTWARE

14.1 PANEL IDENTIFIER

ECTION [3011]

(Default = 0000) The Panel Identifier identifies the control panel to WinLoad

before initiating upload or download. The control panel will verify if the

Panel Identifier in WinLoad is the same. If the codes do not match, the

control panel will not establish communication. Therefore, program the

same Panel Identifier into both the control panel and WinLoad. Enter the

desired 4-digit hexadecimal number into section [3011].

14.2 PC PASSWORD

ECTION [3012]

(Default = 0000) The PC Password identifies the computer running the

WinLoad software to the control panel before beginning the download

process. Program the same PC Password into both the control panel and

WinLoad. If the passwords do not match, WinLoad will not establish

communication. Enter the desired four-digit hexadecimal number into

section [3012].

14.3 PC TELEPHONE NUMBER

ECTION [3010]

The control panel dials this number to communicate with a computer using

WinLoad. Enter any digit from 0 to 9 and any special keys or functions (see

Tab le 3, Special Telephone Number Keys, on page 26) up to a maximum of

32 digits into section [3010].

14.4 CALL BACK FEATURE

ECTION [3037]: OPTION [1]

(Default = disabled) The Call Back Feature provides additional security.

When option [1] is enabled and a computer using WinLoad attempts to

communicate with the control panel, the control panel hangs up and calls

the computer back to re-verify identification codes and re-establish

communication. When the control panel hangs up, WinLoad automatically

goes into Wait For Call Mode (see WinLoad’s Online Help), ready to

answer when the control panel calls back. The PC Telephone Number must

be programmed (see section 14.3).

14.5 CALL WINLOAD

Dial the PC Telephone Number programmed in section [3010] to

communicate with WinLoad. The control panel and WinLoad verify that the

Panel Identifier and the PC Password match before establishing

communication.

WinLoad must be in Wait For Call Mode (see WinLoad’s Online

Help).

For LCD Keypads: Press and hold the [0] key, enter your [

INSTALLER

CODE] and then press [FORCE].

For Grafica Keypads: Press and hold the [0] key, enter your [INSTALLER

CODE], press the center action key (Options), highlight Call WinLoad and

then press the left action key (Select).

14.6 ANSWER WINLOAD

To perform on-site uploading/downloading, connect the computer directly to

the control panel using an ADP-1 line adapter. In WinLoad set Dialing

Condition to Blind Dial. Program the PC telephone number in WinLoad and

follow the ADP-1 Adapter‘s instructions. When the computer has dialed...

For LCD Keypads: Press and hold the [0] key, enter the [

INSTALLER CODE]

and press [

ARM] to manually answer WinLoad from the panel. Press

[

DISARM] to hang up.

For Grafica Keypads: Press and hold the [0] key, enter the [INSTALLER

CODE], press the center action key (Options), highlight Answer WinLoad

and then press the left action key (Select). To hang up, highlight Cancel

Communication and then press the left action key (Select).

14.7 ANSWERING MACHINE OVERRIDE DELAY

ECTION [3052]

(Default = 008) If WinLoad will be used to communicate with an installation

that uses an answering machine or service, program the Answering

Machine Override. If the installation is called back within the programmed

delay period, the Answering Machine Override will bypass the answering

machine or service by picking up the line on the first ring. Also, see section

14.8.

In section [3052] program a value (00 to 15 X 4 seconds, 00 = disabled)

representing the delay period the control panel will wait between the first

and second call.

To use:

Step 1: Using WinLoad, call the installation and on the second ring press

the [

ENTER] key on the keyboard to hang up or hang up manually.

Step 2: After hanging up, WinLoad will immediately call the installation back

or call the site back manually.

For example, an answering machine is set to answer after three rings and

section [3052] is programmed with 10 (10 x 4 = 40 seconds). During the

first call with WinLoad, wait two rings and press [

ENTER]. WinLoad will

immediately call the site back. If the second call is made within 40 seconds,

the control panel will pick up the line on the first ring. If it takes more than 40

seconds, the control panel will not answer on the first ring and the

answering machine will answer after three rings.

14.8 RING COUNTER

ECTION [3051]

(Default = 008) The Ring Counter represents the number of rings the

control panel will wait before picking up the line. If the line is not answered

after the number of programmed rings, the control panel answers the call. If

more than 10 seconds pass between each ring, the Ring Counter resets.

Also, see section 14.7. Enter any value between 01 to 15 (00 = disabled) to

determine the number of rings.

14.9 EVENT BUFFER TRANSMISSION

ECTION [3037]: OPTION [2]

(Default = disabled) Once the Event Buffer contains 1998 events since the

last upload, the control panel makes two attempts to establish

communication with a computer using WinLoad by calling the PC

Telephone Number programmed in section [3010]. WinLoad must be in

Wait To Dial mode. When communication is established, the control panel

uploads the contents of the Event Buffer to WinLoad. If communication is

interrupted before completing transmission or communication is not

established after two attempts, the control panel wait until the Event Buffer

receives another 1998 events before attempting Event Buffer Transmission.

When the Event Buffer is full, each subsequent new event will erase the

oldest event in the buffer. The Event Buffer can hold 2048 Events.

1 2 ... 38 39 40 41 42 43 44 45 46 47 48 ... 63 64

Commentaires sur ces manuels

Pas de commentaire

SEKURE DGP2-648 Manuel d'installation Page 43

Commentaires sur ces manuels

Produits connexes et manuels pour Systèmes de contrôle d'accès de sécurité SEKURE DGP2-648