SEKURE DGP2-648 Manuel d'installation télécharger pdf (Page 20)

18 REFERENCE & INSTALLATION MANUAL

6 ARMING AND DISARMING OPTIONS

6.1 ARMING FOLLOWS PARTITION

(Default = disabled) A partition can be set to follow the arming and

disarming status of one or more partitions. If a partition is set to follow more

than one partition, the partition will arm when all the selected partitions are

armed. However, the partition will disarm as soon as one of the selected

partitions is disarmed.

For example, if options [2] and [3] are ON in section [3121], Partition 1 will

automatically arm whenever partitions 2 and 3 are armed. Partition 1 will

disarm when either partition 2 or partition 3 is disarmed.

6.2 RESTRICT ARMING ON SUPERVISION LOSS

ECTION [3034]: OPTION [4]

(Default = disabled) When option [4] is enabled, the control panel can

restrict arming if it receives a supervision loss signal from the Omnia

433MHz Wireless System OMN-RCV3 (see section 7.3). Partitions will not

arm until all supervision loss trouble conditions are corrected.

6.3 RESTRICT ARMING ON TAMPER

SECTION [3034]: OPTION [8]

(Default = disabled) When option [8] is enabled, the control panel prevents

arming if it detects a tamper on a zone or module (see section 7.5).

Partitions will not arm until the Installer Code is entered and tamper trouble

conditions are corrected.

6.4 RESTRICT ARMING ON AC FAILURE

ECTION [3035]: OPTION [1]

(Default = disabled) When option [1] is enabled, the control panel can

prevent arming if it detects a loss of AC power. Partitions will not arm until

power is restored.

6.5 RESTRICT ARMING ON BATTERY FAILURE

ECTION [3035]: OPTION [2]

(Default = disabled) When option [2] is enabled, the control panel prevents

arming if it detects a battery loss or if the battery voltage is less than 10.5V.

The control panel will not arm a partition until all battery trouble conditions

are corrected.

6.6 RESTRICT ARMING ON BELL OR AUXILIARY FAILURE

ECTION [3035]: OPTION [3]

(Default = disabled) When option [3] is enabled, the control panel can

prevent arming if it detects that:

• the bell or siren is disconnected

• the Bell Output has exceeded its current limits

• the Auxiliary Outputs have exceeded their current limits

The control panel will not arm any partition until all bell or auxiliary trouble

conditions are corrected.

6.7 RESTRICT ARMING ON TLM FAILURE

ECTION [3035]: OPTION [4]

(Default = disabled) When option [4] is enabled, the control panel can

prevent arming if it is unable to access the telephone line. The control panel

will not arm any partition until all TLM trouble conditions are corrected.

6.8 RESTRICT ARMING ON MODULE TROUBLES

ECTION [3035]: OPTION [5]

(Default = disabled) When option [5] is enabled, the control panel will

monitor the same Restrict Arming options selected for the control panel

(battery, tamper, supervision, AC, bell, auxiliary and/or TLM failures) for the

modules connected to the combus. The control panel will prevent arming if

the control panel detects the equivalent trouble condition occurring on a

module.

For example, if options [1], [2] and [5] are ON in section [3035], the control

panel prevents arming if it detects an AC or battery failure on the control

panel or on a module connected to the combus.

6.9 TIMED AUTO-ARMING

(Default = disabled) When this option is enabled, the control panel arms the

selected partition every day at the time set by the Auto-Arm Timer (see

section 6.9.1). A 60-second Exit Delay triggers before the partition arms,

but Auto-Arming can be cancelled by entering a valid access code. The

Auto-Arming Option sets the arming method (see section 6.11). If zones are

open when a partition is Auto-Armed, the control panel arms the partition

and considers all open zones as temporarily bypassed (except 24hr.

zones).

When the partition Auto-Arms, the control panel transmits the Auto-Arming

report code programmed in section [3910]. Whether the partition was

successfully armed or not, the control panel will always transmit the Late to

Close report code programmed in section [3912]. Enable option [1] in the

desired section:

Partition 1: [3121]

Partition 1 arms & disarms with:

Option [1] = N/A

Option [2] = Partition 2

Option [3] = Partition 3

Option [4] = Partition 4

Option [5] = Partition 5

Option [6] = Partition 6

Option [7] = Partition 7

Option [8] = Partition 8

Partition 5: [3521]

Partition 5 arms & disarms with:

Option [1] = Partition 1

Option [2] = Partition 2

Option [3] = Partition 3

Option [4] = Partition 4

Option [5] = N/A

Option [6] = Partition 6

Option [7] = Partition 7

Option [8] = Partition 8

Partition 2: [3221]

Partition 2 arms & disarms with:

Option [1] = Partition 1

Option [2] = N/A

Option [3] = Partition 3

Option [4] = Partition 4

Option [5] = Partition 5

Option [6] = Partition 6

Option [7] = Partition 7

Option [8] = Partition 8

Partition 6: [3621]

Partition 6 arms & disarms with:

Option [1] = Partition 1

Option [2] = Partition 2

Option [3] = Partition 3

Option [4] = Partition 4

Option [5] = Partition 5

Option [6] = N/A

Option [7] = Partition 7

Option [8] = Partition 8

Partition 3: [3321]

Partition 3 arms & disarms with:

Option [1] = Partition 1

Option [2] = Partition 2

Option [3] = N/A

Option [4] = Partition 4

Option [5] = Partition 5

Option [6] = Partition 6

Option [7] = Partition 7

Option [8] = Partition 8

Partition 7: [3721]

Partition 7 arms & disarms with:

Option [1] = Partition 1

Option [2] = Partition 2

Option [3] = Partition 3

Option [4] = Partition 4

Option [5] = Partition 5

Option [6] = Partition 6

Option [7] = N/A

Option [8] = Partition 8

Partition 4: [3421]

Partition 4 arms & disarms with:

Option [1] = Partition 1

Option [2] = Partition 2

Option [3] = Partition 3

Option [4] = N/A

Option [5] = Partition 5

Option [6] = Partition 6

Option [7] = Partition 7

Option [8] = Partition 8

Partition 8: [3821]

Partition 8 arms & disarms with:

Option [1] = Partition 1

Option [2] = Partition 2

Option [3] = Partition 3

Option [4] = Partition 4

Option [5] = Partition 5

Option [6] = Partition 6

Option [7] = Partition 7

Option [8] = N/A

Partition 1: [3122] Partition 3: [3322] Partition 5: [3522] Partition 7: [3722]

Partition 2: [3222] Partition 4: [3422] Partition 6: [3622] Partition 8: [3822]

1 2 ... 15 16 17 18 19 20 21 22 23 24 25 ... 63 64

Commentaires sur ces manuels

Pas de commentaire

SEKURE DGP2-648 Manuel d'installation Page 20

Commentaires sur ces manuels

Produits connexes et manuels pour Systèmes de contrôle d'accès de sécurité SEKURE DGP2-648