SEKURE DGP2-648 Manuel d'installation télécharger pdf (Page 7)

DIGIPLEXNE CONTROL PANEL 5

Figure 2-3: DigiplexNE Control Panel Wiring Diagram

When installing the combus wires in a noisy environment, or

when connecting the combus across separate buildings, you

must use a shielded cable. Refer to section 2.16.1 on page 9.

PLEASE NOTE: When powering up the DGP-NE96 control panel (V1.02 or higher), the panel will begin a module scan to verify if all the modules connected to the panel are operational. The scanning

process will take between 30 and 120 seconds to complete depending on the number of modules connected to the control panel. The module scan is complete when the LCD keypad begins to show the

partition status. Only after the module scan is complete will the control panel be fully operational.

PLEASE NOTE: It is strongly recommended that you test your

system on a weekly basis, and have your system checked by a

qualified technician a minimum of every 3 years.

Please see “UL and ULC Warnings” on page 59 for applicable

UL/ULC warnings and information.

The combus supports a maximum of 127 modules. Although

external power supplies can be used to provide power to

modules connected far from the control panel, the total

distance of all runs of wire combined cannot exceed 914m

(3000ft). For example, if ten runs of wire measuring 305m

(1000ft) each are connected to the control panel, the total

distance would be 3048m (10, 000ft), which exceeds the

system's capacity.

WARNING: Before adding any module to the control panel

make sure you shutdown the control panel by removing AC

power and the battery.

Door Contact

* if EOL is enabled in the

control panel

*A 1K

9 resistor is

required if the Bell is

not equipped with an

internal resistor. The

resistor must be

connected between

the Bell's negative (-)

and positive (+) wires.

Position the resistor as

close as possible to

the Bell. A resistor is

not required for sirens.

The "bell"

output will

shutdown if

the current

exceeds 3A.

Bell/Siren

1K9

resistor*

Bell/Siren

1K9

resistor*

Transformer Requirements: Minimum:

16.5VAC; 20VA

Auxiliary Supply can provide: typical 600mA

max. 700mA

Usable Battery Charge 350mA

Currents:

AUX Power (Auxiliary):

Refer to the transformer requirements for the

Auxiliary Power Output. Also, refer to the

Power Unit Consumption Table. To connect

additional wiring to auxiliary power, use the

red (+) and black (-) keypad connectors.

Auxiliary power will shut down if the current

exceeds 1.1A.

WARNING:

Improper connection may result

in damage to the system.

To provide maximum lightning protection we

strongly recommend having separate earth

connections for the dialer and zone ground

terminals.

AWG#14 single

conductor

solid copper

wire

Ground

clamp

Cold water pipe

grounding

To metallic

enclosure

For the hardwired connections, see Single Zone Input

Connections on page 8 and Double Zone Connections

on page 8.

Combus

CAUTION: Disconnect

the battery before

replacing the fuse.

Optional connector can

be used to recharge

another battery in the

system or to the

connect a secondary

battery.

WARNING!

Do not connect a DGP2-TM1

Time Module to the

"mem key/tm1" connector.

Connecting a DGP2-TM1 will

create time errors within the

panel and features that use the

control panel's internal clock

(ex.: Auto-arming) will not

function correctly.

Reset Jumper

Same ground

connections as the

panel, but do not connect

the DGP2-ZX4's ground

directly to the control

panel's ground.

For the hardwire connections,

see Single Zone and Double

Zone Connections.

Four pin connector can

be used for quick

installation of a keypad

or module.

Built-in RTC

Commentaires sur ces manuels

Pas de commentaire

SEKURE DGP2-648 Manuel d'installation Page 7

Commentaires sur ces manuels

Produits connexes et manuels pour Systèmes de contrôle d'accès de sécurité SEKURE DGP2-648