SEKURE DGP2-648 Manuel d'installation télécharger pdf (Page 16)

14 REFERENCE & INSTALLATION MANUAL

4.3.10 24Hr Water Zones*

SECTIONS [0101] TO [0196]: FIRST DIGIT = A

When a 24Hr Water zone opens, whether it is armed or disarmed, the

control panel will immediately generate an alarm. The SIA FSK reporting

format includes specific codes to identify the alarm as a Water Alarm.

4.3.11 24Hr Freeze Zones*

SECTIONS [0101] TO [0196]: FIRST DIGIT = B

When a 24Hr Freeze zone opens, whether it is armed or disarmed, the

control panel will immediately generate an alarm. The SIA FSK reporting

format includes specific codes to identify the alarm as a Freeze Alarm.

* UL Note: UL Listed compatible devices shall be used for UL systems. For

UL Listed systems, this type of zone shall be programmed as a silent auxiliary

alarm.

4.3.12 Delayed 24Hr Fire Zone (Not to be used with UL Listed systems)

SECTIONS [0101] TO [0196]: FIRST DIGIT = C

The Delayed 24Hr Fire Zone definition from Figure 4-3: on page 14 is

commonly used in residential homes where a smoke detector often

generates false alarms (i.e. cigarette smoke, burning bread, etc.). A zone

programmed as Fire becomes normally open (will not function as normally

closed) and requires an EOL resistor.

The keypads must be assigned to the same partition as the

Delayed 24Hr Fire zone for the buzzer to activate.

Figure 4-3: Delayed 24Hr Fire Zone

4.3.13 Standard 24Hr Fire Zone

SECTIONS [0101] TO [0196]: FIRST DIGIT = D

A zone programmed as Fire becomes normally open (will not function as

normally closed) and requires an EOL resistor.

When a Standard 24Hr Fire Zone triggers, the control panel can:

• send a Zone Alarm report code (see section 8.2.1 on page 24).

• send a Fire Loop Trouble Report (see section 8.2.11 on page 25) if a

tamper/wiring fault occurs on a Fire Zone. A “Zone Fault Trouble” will

also appear in the keypad's Trouble Display.

• generate a Fire alarm, which is always audible, regardless of other

settings. Fire alarms generate an intermittent signal (see Figure 4-4).

Figure 4-4: Bell/Siren Output During Fire Alarm

4.3.14 Stay Delay Zone

SECTIONS [0101] TO [0196]: FIRST DIGIT = E AND F

When a Stay Delay zone is armed using the Regular or Force arming

methods, the control panel processes the zone as an Instant zone (see

section 4.3.4). When a Stay Delay zone is armed using the Stay or Instant

arming methods and the zone is triggered, the control panel will not

generate an alarm until the programmed Stay Delay elapses. A zone

defined as Stay Delay 1 follows the Entry Delay 1 Timer of its assigned

partition. Likewise, a zone defined as Stay Delay 2 follows the Entry Delay

2 Timer of its assigned partition. To program the Entry Delay Timers, refer

to Entry Delays 1 and 2 on page 13.

For example, if zone 1 in Partition 5 is defined as Stay Delay 1, the timer

will follow the amount programmed in [3511].

4.4 ZONE PARTITION ASSIGNMENT

ECTIONS [0101] TO [0196]: SECOND DIGIT = 1 TO 8

A control panel can be divided into eight completely independent systems

(see section 11.9 on page 32). Assign each zone to one partition (see

Figure 4-1 on page 12).

4.5 ZONE OPTIONS

The zone options from Figure 4-1 on page 12 are described below.

4.5.1 Auto Zone Shutdown

SECTIONS [0101] TO [0196]: OPTION [1]

(Default = 000) When option [1] is disabled, the control panel generates an

alarm when an armed zone is breached even if the same zone opens

repeatedly during the same alarm, which may cause several reportings and

further activation of the bell output. When option [1] is enabled, the control

panel will stop regenerating alarms on the zone during the same armed

period once the Auto Zone Shutdown Limit is reached. The Auto Zone

Shutdown Limit resets every time the system is armed. To program the

Auto Zone Shutdown Limit, key in the desired 3-digit counter (000 to 255)

into section corresponding to the desired partition (000 = disabled):

4.5.2 Bypass Zones

SECTIONS [0101] TO [0196]: OPTION [2]

Only zones with option [2] enabled can be Manually Bypassed (see section

15.7). Fire Zones cannot be bypassed. Default = enabled.

Delayed Fire Zone

Triggered

Activate bell/siren output & delay

report transmission for 30 seconds.

Yes

Any key on

keypad pressed

within 30

seconds?

Bell/siren silenced. Delay report

transmission an additional 90 sec.

Problem

corrected?

Latch alarm and transmit

report code as described

in the section "Standard

24Hr. Fire Zone".

END

Alarm Disabled

Has a 2nd

Delayed Fire

Zone opened in

30 sec.?

Yes

Has the zone

closed within

30 seconds?

Yes

Partition 1: [3114] Partition 5: [3514]

Partition 2: [3214] Partition 6: [3614]

Partition 3: [3314] Partition 7: [3714]

Partition 4: [3414] Partition 8: [3814]

1 2 ... 11 12 13 14 15 16 17 18 19 20 21 ... 63 64

Commentaires sur ces manuels

Pas de commentaire

SEKURE DGP2-648 Manuel d'installation Page 16

Commentaires sur ces manuels

Produits connexes et manuels pour Systèmes de contrôle d'accès de sécurité SEKURE DGP2-648