SEKURE DGP2-641 Manuel d'installation télécharger pdf (Page 37)

IGIPLEX

NE C

ONTROL

ANEL

12.1 H

ARDWARE

ESET

A Hardware Reset sets sections [0001] to [3991] to default, including the

Installer and System Master Codes. Only the Panel ID, PC Password, PC

Telephone Number and Event Buffer are not reset. A Hardware Reset

cannot be performed on a control panel with the Installer Code Lock

enabled (see section 12.3).

1) Make sure the Installer Code Lock is disabled

2) Remove the battery and AC power from the control panel.

3) Place the

RESET

jumper on the reset pins of the control panel.

4) Re-connect the AC power and the battery to the control panel.

5) Wait 10 seconds and remove the jumper.

12.2 S

OFTWARE

ESET

Performing a software reset will set certain parameters to default values or

program certain sections with a set of pre-defined values. To do so:

1) Place the

RESET

jumper on the reset pins of the control panel.

2) Enter Panel Programming Mode (see section 4.4).

3) Enter the 4-digit [

SECTION

] of the software reset you wish to perform:

Do not remove power from the control panel.

12.3 I

NSTALLER

ODE

OCK

(Default = 000) Enter 147 into section [3001] to lock all programming.

When 147 is programmed, performing a hardware reset as described in

section 12.1 will not affect the current panel settings. To remove the

Installer Lock, enter 000 into section [3001].

12.4 D

AYLIGHT

AVINGS

IME

(Default = enabled) When option [3] is enabled, the control panel adjusts

the system's clock (time) for daylight saving changes. At 2:00AM on the first

Sunday of a full weekend in April, the control panel will add one hour to the

programmed time (clock). At 2:00AM on the last Sunday of a full weekend

in October, the control panel will subtract one hour from the time (clock).

12.5 B

ATTERY

HARGE

URRENT

When option [5] is enabled, the battery’s charge current is 700mA (min.

40VA transformer). When option [5] is disabled, the charge current is

350mA. Depending on the battery’s capacity, enable or disable the option:

12.6 S

ERIAL

ORT

AUD

ATE

When option [8] is enabled, the serial port’s baud rate is 38,400 baud.

When option [8] is disabled, the baud rate is 19,200 baud. Depending on

the baud rate set in WinLoad or NEware, enable or disable option [8]:

If communication between the control panel and the computer is

experiencing difficulty at 38,400 baud, especially over long

distances, disable option [8] and reduce the baud rate of the

software to 19,200 baud.

12.7 P

ARTITIONING

(Default = only partition 1 enabled) The control panel can provide up to

eight completely independent partitions. Most features and options can be

independently set for each partition such as Event Reporting, Entry/Exit

Delay, Bell Squawk, One-touch Arming, Panic Alarms and many more. All

zones, keyswitch zones, user codes and system modules are assigned to

specific partitions, making this a true partitioned system. Enable the

option(s) that correspond to the desired partition(s):

12.7.1 Panel Partition Assignment

(Default = 00) The control panel will report system events as originating

from one or all enabled partitions. The System Troubles (i.e. AC Failure,

TLM Failure, etc.) can only be viewed through the partitions enabled in this

section. Enter one of the following values:.

Section Description

[4040]

Entering this section resets the programmable sections from

[0001] to [3991] to default (even if Installer Code Lock is

enabled). The Event Buffer, Panel ID, PC Password, PC

Telephone Number and Zone, Door, Partition and User Labels

(see section 13.4) will not reset.

[4041] Entering this section resets the System Master Code to 123456.

[4042]

Entering this section resets all Zone Programming sections from

[0001] to [0196], [0201] to [0296] and [0961] to [0984] to default.

[4043]

Entering this section resets the Access Control sections, except

Door Labels (see section 12.22), from [2201] to [2712] to default.

[4044]

Entering this section resets all User Access Code Programming

sections from [1001] to [1999] and [2001] to [2199] to default.

User Labels (see section 13.4) will not be reset.

[4045]

Entering this section resets all control panel settings from [3020]

to [3043] and from [3900] to [3991] and all the Dialer sections

from [3051] to [3081] to default.

[4046]

Entering this section resets all Partition Settings, except Partition

Labels (see section 12.22), from [3101] to [3829] to default.

[4047]

Entering this section resets Keyswitch Programming sections

from [0501] to [0832] and all Programmable Outputs sections

from [0901] to [0939] to default.

[4048]

Entering this section resets the User Labels from the User

Access Codes, the Zone Labels from [0301] to [0396], Door

Labels from [2301] to [2332], Partition Labels [3100], [3200],

[3300], [3400], [3500], [3600], [3700] and [3800] to default.

Option Feature

[5]

700mA

[5]

OFF

350mA (default)

Option Feature

[8]

38,400 baud

[8]

OFF

19,200 baud (default)

Option Description Option Description

[1] Partition 1 [5] Partition 5

[2] Partition 2 [6] Partition 6

[3] Partition 3 [7] Partition 7

[4] Partition 4 [8] Partition 8

Value Description Value Description

00 All enabled partitions

01 Control Panel in Partition 1 05 Control Panel in Partition 5

02 Control Panel in Partition 2 06 Control Panel in Partition 6

03 Control Panel in Partition 3 07 Control Panel in Partition 7

04 Control Panel in Partition 4 08 Control Panel in Partition 8

1 2 ... 32 33 34 35 36 37 38 39 40 41 42 ... 65 66

Commentaires sur ces manuels

Pas de commentaire

SEKURE DGP2-641 Manuel d'installation Page 37

Commentaires sur ces manuels

Produits connexes et manuels pour Systèmes de contrôle d'accès de sécurité SEKURE DGP2-641